MODELLING OF AIRFLOW AND WOOD DRYING INSIDE A KILN : A COMPREHENSIVE APPROACH.

Código QR

MODELLING OF AIRFLOW AND WOOD DRYING INSIDE A KILN : A COMPREHENSIVE APPROACH.

Detalles Bibliográficos
Autor principal:	POUGATCH, KONSTANTIN
Formato:	Artículo
Lenguaje:	Spanish
Materias:	MADERA MODELADO SECADO PROPIEDADES DUREZA RESISTENCIA Artículos de revista

Ejemplares similares

THE INFLUENCE OF DRYING METHOD ON THE WARP BEHAVIOR OF NORWAY SPRUCE (PICEA ABIES L. KARST) SAWN TIMBER.
por: KLAIBER, VOLKER

A comparison of kiln - drying schedules and quality outcomes for 4 /
por: Matthew S. Scholl ... [Et al.]

INDUCTION OF A PERMEABILITY GRADIENT IN KILN DRIED PONDEROSA PINE.
por: WALLACE, BENJAMIN L.

CROOK AND OVERLENGTHH IN HARDWOOD LUMBER : RESULTS FROM A 14 MILL SURVEY.
por: WIEDENBECK, JAN

HEAT AND MASS TRANSFER MODEL IN WOOD CHIP DRYING.
por: DE PAIVA SOUZA, MARIA EUGENIA

COLOR RESPONSE IN SILVER BIRCH DURING KILN-DRYING.
por: STENUDD, STEFAN

Accelerated drying of plantation grown Eucalyptus cloeziana and Eucalyptus pellita sawn timber /
por: Redman, Adam L.

TWIST ASSESSMENT AND REDUCTION IN SOUTHERN PINE 2 BY 4´S.
por: SNMULSKY, RUBIN

Kiln-Drying of Lumber /
por: Keey, Roger B.
Publicado: (2000)

MACHINING-INDUCED SUBSURFACE DAMAGE OF WOOD; ANDRES L. CARRANO, JAMES TAYLOR, RICHARD LEMASTER.
por: CARRANO, ANDRES

REDUCTION IN KILN-DRYING TIME FOR BLACK CHERRY LUMBER.
por: SCHOLL, MATTHEW S.

POTENTIAL SOURCES OF VARIATION THAT INFLUENCE THE FINAL MOISTURE CONTENT OF KILN-DRIED HARDWOOD LUMBER.
por: HONGMEI GU... [ET AL.]

Performance of antisapstain compounds on kiln-dried Douglas-firand hem-fir lumber subjected to rewetting.
por: Melencion, Neil

INVESTIGATION OF BOILING FRONT DURING VACUUM DRYING OF WOOD.
por: CHEN, ZHANGJING

Effect of kiln - drying on the hardness and machining properties of tamarack wood for flooring.
por: Cecilia Bustos, Roger E. Hernández, Yves Fortin

Impact of mountain pine beetle (MPB) attack on drying characteristics of wood.
por: Cai, Liping

VACCUM DRYING OF SMALL WOOD COMPONENTS AT ROOM TEMPERATURE; ZHANGJING CHEN, FRED M. LAMB.
por: CHEN, ZHAGJING

Bending performance of composite wood I-joist/oriented strand board panel assemblies /
por: Davids, William G.

Timber drying manual.
por: Pratt, G. H.
Publicado: (1974)

TOTAL ORGANIC COMPOUNDS RELEASED FROM DEHUMIDIFICATION DRYING OF AIR-DRIED HARDWOOD LUMBER.
por: BEAKLER, BRIAN W.

The simultaneous treatment of compression drying and deformation fixation in the compression processing of wood.
por: Fukuta, Satoshi

EXPERIMENTAL BEHAVIOR OF A CONTINUOUS METAL CONNECTOR FOR A WOOD- CONCRETE COMPOSITE SYSTEM; PEGGI CLOUSTON, SCOTT CIVJAN, LEANDER BATHON.
por: CLOUSTON, PEGGI

Water vapor adsorption in kiln-dried red oak.
por: Zhang, Minghui

Theoretical modeling of bonding characteristics and performance of wood composites. Part IV. Internal bond strengt.
por: Dai, C.

Wood-adhesive interface characterization and modeling in engineered wood floorin.
por: Belleville, Benoît

Dynamic viscoelastic properties of wood treated by three drying methods measured at high-temperature range.
por: Jiang, Jiali

Characterization of tangential shrinkage stresses of wood during drying under superheated steam above 100 ºC..
por: Cheng, Wanli

A method for optimizing lumber sorting before kiln-drying.
por: Elustondo, Diego Miguel

Modeling wood strands as multi-layer composites : bending and tension loads.
por: Hindman, Daniel P.

Cell wall porosity in norway spruce wood as affected by high-temperature drying /
por: Borrega, Marc

ANALYTICAL MODELING OF RHEOLOGICAL POSTBUCKLING BEHAVIOR OF WOOD-BASED COMPOSITE PANELS UNDER CYCLIC HYGRO-LOADING.
por: KANG, WOOK

Modeling biomass collection and woods processing life-cycle analysis /
por: Johnson, Leonard

Optimization of pressing parameters for mechanically surface - densified aspen.
por: Lamason, Clevan

HARDWOOD LUMBER WIDTHS AND GRADES USED BY THE FURNITURE AND CABINET INDUSTRIES : RESULTS OF A I 4 MILL SURVEY.
por: WIEDENBECK, JAN

Strength properties of juvenile and mature wood in black locust (Robinia Pseudoacacia L.).
por: Adamopoulos, Stergios

Theoretical modeling of bonding characteristics and performance of wood composites. Part III : Bonding strength between two wood element.
por: He, Guangbo

Theoretical modeling of bonding characteristics and performance of wood composites. Part II : Resin distribution.
por: Dai, Chunping

FUZZY KNOWLEDGE-BASED MODELING AND STATISTICAL REGRESSION IN ABRASIVE WOOD MACHINING; ANDRES CARRANO ... [ET AL.].

Use of nanoindentation and silviscan to determine the mechanical properties of 10 hardwood species.
por: Wu, Yan

WITHDRAWAL STRENGTH AND MOMENT RESISTANCE OF SCREWED T-TYPE END-TO-SIDE GRAIN FURNITURE JOINTS.
por: EFE, HASAN