Dynamic Behavior of Materials, Volume 1 : Proceedings of the 2012 Annual Conference on Experimental and Applied Mechanics - Chalivendra, Vijay; Song, Bo.; Casem, Daniel; SpringerLink (Online service) (New York, NY : Springer New York : Imprint: Springer, 2013)
Correlation of Structural Strain to Tip Vorticity and Lift for a MAV Pliant Membrane Wing -- Deformation Mapping at the Microstructural Length Scale -- Molecular Tailoring of Interfacial Adhesion Using Self-assembled Monolayers -- Micromechanical Characterization of Ductile Damage in DP Steel -- MEMS Device for Fatigue Testing 25 Micrometer Thick Aluminum Specimens -- High Confidence Level Calibration for AFM Based Fracture Testing of Nanobeams -- High Strain Rate Characteristics of Fiber Bragg Grating Strain sensors -- Dynamic Shape and Strain Measurements of Rotating Tire in Time-series -- Measurement of Metallic Adhesion Force-to-Elongation Profile Under High Separation-Rate Conditions -- Prediction of Constraint Parameters Along the 3D Crack Front Under Negative Biaxial Loadings -- Role of Viscoelasticity in Predicting the Shape Memory Effect of Polymers -- Damage Assessment in Syracuse Limestone Specimens by Frequency Analysis of Elastic Emissions -- Photogrammetry Measurements During a Tanking Test on the Space Shuttle External Tank, ET-137 -- Experimental, Numerical and Analytical Evaluation of Structural Integrity of Experiment Container Subjected to Reduced Gravity Flight Testing -- Use of Fiber Bragg Grating Strain Gages on a Pipeline Specimen Repaired With a CFRE Composite System -- Microstructure in the FSW Butt Joint of Aluminum Alloy AA5083 -- Load History Dependency of Plastic Collapse Behavior of Cracked Piping -- Production of Metal Matrix Composites Using Thixinfiltration Techniques -- Review of Methods for Determining Residual Stresses in Biological Materials -- A Comparison of Residual Stress Measurements on Linear Friction Welds Using the Contour Method and Neutron Diffraction -- Experimental Study of High Speed Ball End milling of Titanium Alloy (Ti-6Al-4V) -- Very High-cycle Fatigue Resistance of Shot Peened High-strength Aluminum Alloys -- The Application of the Combined Creep and Rate-independent Plasticity Model to Turbine Components Life Prediction -- Modified Constitutive Relation Error Strategy for Elastic Properties Identification -- Identification of the Anisotropic Plastic Behaviour of Sheet Metals at Large Strains -- Cohesive Zone Law Extraction From an Experimental Peel Test -- Application of a New Experimental Method to Determine Bi-material Interface Bonding Strength -- Calibration of Barkhausen Noise for Residual Stress Measurement -- Film Residual Stress Assessment Method via Temporarily Thermal Relaxation -- Determining Residual Stresses With the Aid of Optical Interference Techniques -- Interfacial Fracture Toughness and Residual Stress of Thermally Sprayed Coatings -- Design of Ultrasonic Probe Configuration Using Finite-difference Time Domain Simulation -- Absorbed vs. Released Energy in the Cracking Process of Heterogeneous Materials Under Compression -- Detailed Measurements of Thread Deformation and Failure in Thin Walled Aluminum Alloy Joints -- Experimental Characterization of Integral Invariants in Wood Specimen Using the full Field Optical Technique -- Stress intensity factors for viscoelastic axisymmetric problems applied to wood -- Simulation of Interference Fitted Joint Strength as Used in Hot Rolling Work Rolls -- Modelling of Nosing for the Assembly of Aerospace Bearings -- Multi-axial Quasi-static Strength of a Clinched Sheet Metal Assembly -- Simplified Calculation Method of the Torsion Effect on the Seismic Behavior of Timber Buildings -- Experimental Analysis of the Semi-rigidity Joint in the Standardized Timber Beam -- Nano-Macro Correlation of Nano-Silica Concrete -- Experimental results of green wood slice under natural drying -- Structural Health Monitoring in the Area of Coal Exploitation -- Thickness Effect on Cross-ply GLARE 5 FML Beams Subjected to Ballistic Impact -- Hole-drilling Residual Stress Measurement in an Intermediate Thickness Specimen -- Effects of Strain's Error on Residual Stresses Calculated by HDM -- Hole-drilling Residual Stress Measurement With Artifact Correction Using Full-field DIC -- Anisotropic and Pressure-dependent Plasticity Modeling for Residual Stress Prediction -- Simulation of Triaxial Residual Stress Mapping for a Hollow Cylinder -- Use of Vision-based Methods for Measurement of Mechanical Properties of Exhaust Catalysts -- Design & Development of Ring Shaped Force Transducers -- Novel High Resolution Sensor Concept -- Development of a Test Simulator to Perform Optimized Experiment Design -- Interval identification of constitutive parameters of fractional viscoelastic models.
Keywords: Mechanics; Mechanics, Applied; Materials science; Theoretical and Applied Mechanics; Classical Mechanics; Materials Science, general